Martin-universal-design U-115N MIDDLEWEIGHT FOLDING EASEL Manuel d'utilisateur télécharger pdf

U-115N/L Middleweight Folding Easel

ASSEMBLY INSTRUCTIONS

HARDWARE PARTS

1 ea. .......3” Bolts [A]

2 ea. .......2½” Bolts [B]

3 ea. .......2” Bolts [C]

2 ea. .......1” Wood Screws [D]

2 ea. .......½” Wood Screws [E]

3 ea. .......Washers [F]

3 ea. .......Wingnuts [G]

2 ea. .......Plastic Channel Guides [H]

2 ea. .......Plastic Knobs [I]

1 ea. .......Metal Stay [J]

WOOD PARTS

1 ea. .......Channelled Center Column

1 ea. .......Rear Spike Leg

........with attached wooden block

1 ea. .......Base Foot

1 ea. .......Upper Canvas Support

1 ea. .......Lower Canvas Support

MAKE SURE CARTON CONTAINS THE FOLLOWING PARTS

Layout all wood parts

on hard flat floor

with all holes facing up.

STEP 1. Before Attaching Rear Spike Leg.

MAKE SURE rear leg is in this position before

attaching to Channelled Center Column.

Continue by aligning screw holes and proceed

by screwing in 2 ea. 1” wood screws [D] into

wood block and then into upper cross member.

FIG 1

Martin Universal Design, Inc. • 4444 Lawton Avenue, Detroit, MI 48150 USA

Tel:(313)895-0700 • Fax:(313)895-0709 • E-mail:[email protected]

Channelled Center Column

Rear Spike Leg

Upper Canvas Support

Lower Canvas Support

Rear spike leg w/

woodedn block

STEP 2. Attaching Metal Stay [J] to Easel

MAKE SURE Positioning of metal stay [J] is

CORRECT as shown below in FIG. 2.

Align holes in metal stay with pre-tapped holes in

center column. Attach using 2 ea. 1/2” wood

screws [E] and tighten.

Channel in

center column

Metal Stay in Correct Position

FIG 2

Channelled

Center Column

Base Foot

[C] 3ea. -2” Bolts

[B] 2ea. - 2½” Bolts

[D] 2ea.

1” Wood Screws

[F] 3 ea. - Washers

[G] 3 ea. - Wingnuts

2ea.

[H] Plastic Channel Guide

[I] 2ea.

Plastic Knobs

[J] 1ea. - Metal Stay

[E] 2ea.

½” Wood Screws

[A] 1ea. - 3” Bolt

1 2

ASSEMBLY INSTRUCTIONS 1

Résumé du contenu

Page 1 - ASSEMBLY INSTRUCTIONS

U-115N/L Middleweight Folding EaselASSEMBLY INSTRUCTIONSHARDWARE PARTS1 ea. ...3” Bolts [A]2 ea. ...2½” Bolts [B]3 ea. ...2” Bolts [C]2 ea

Page 2

STEP 4. Attaching rear support leg to Metal Stay [J].Take 3” bolt [A] and insert through holeprovided in side of rear support leg. Proceedby adding a

Commentaires sur ces manuels

Pas de commentaire

Martin-universal-design U-115N MIDDLEWEIGHT FOLDING EASEL Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Sports et loisirs Martin-universal-design U-115N MIDDLEWEIGHT FOLDING EASEL. Martin Universal Design U-115N MIDDLEWEIGHT FOLDING EASEL User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Sports et loisirs Martin-universal-design U-115N MIDDLEWEIGHT FOLDING EASEL